| Tactical Command http://www.tacticalwargames.net/taccmd/ |
|
| Constructing a Hellbore http://www.tacticalwargames.net/taccmd/viewtopic.php?f=7&t=2159 |
Page 1 of 1 |
| Author: | dysartes [ Thu Dec 16, 2004 4:10 pm ] |
| Post subject: | Constructing a Hellbore |
OK, one of my eBay wins showed up today - an unbuilt Hellbore. However, there were no instructions on how to put it together, which could be problematic. The main area I can't seem to work out is the hydraulic lifting assembly which the Hellbore sits on top of, as I can't seem to get it to sit right. Help, please? |
|
| Author: | Warmaster Nice [ Thu Dec 16, 2004 5:46 pm ] |
| Post subject: | Constructing a Hellbore |
I'm just speaking from the experience I've had with Moles but unless the Hellbore is placed in a lifted position there's realy no need to use the piston bit. There's no room for it in level position. Not sure if that's any help but just my two cents anyway  Cheers! 
|
|
| Author: | Tas [ Fri Dec 17, 2004 4:04 am ] |
| Post subject: | Constructing a Hellbore |
Why don't you have a look at Carl's fantastic Hellbore at his Dropship website and see if that can help you out? |
|
| Author: | dysartes [ Fri Dec 17, 2004 5:43 am ] |
| Post subject: | Constructing a Hellbore |
Well, Tas, its a very nicely painted Hellbore and all that, but the views it gives don't really give any clues wrt construction, unfortunately 
|
|
| Author: | vanvlak [ Fri Dec 17, 2004 7:35 am ] |
| Post subject: | Constructing a Hellbore |
Hi Dysartes, Nudrgle has struck agaibn and I'm stranded here with a batteryless camera. I'll try to sketch it and send it. |
|
| Author: | vanvlak [ Fri Dec 17, 2004 7:48 am ] |
| Post subject: | Constructing a Hellbore |
Sorry for the double-post - I'd forgotten that edited posts cannot have pics attached. Anyway, hope you can decipher it. Oh God, the writing's terrible - I'll decipher it: Transport mode: ramp pins in grooves 3 (front of transporter); jack pins - thick end in grooves 1 (rear of transporter) and thinner end pins in grooves 2 (forward of the centre of the transporter longitudinally) Launch mode: ramp pins in grooves 3 (front of transporter); jack pins - thick end in grooves 1 (rear of transporter) and thinner end pins in grooves on underside of ramp; grooves 2 unused. Hope this is better.  |
|
| Author: | Mojarn Piett [ Fri Dec 17, 2004 8:14 am ] | ||
| Post subject: | Constructing a Hellbore | ||
Need any help in swatting those plaguebearers? I could send some Grey knights. Get well soon!
|
|||
| Author: | vanvlak [ Fri Dec 17, 2004 8:22 am ] | ||||
| Post subject: | Constructing a Hellbore | ||||
Make my day! Thanks Mojarn. Second  flu of the season.
|
|||||
| Author: | dysartes [ Fri Dec 17, 2004 9:50 am ] |
| Post subject: | Constructing a Hellbore |
OK, vanvlak, I think I see what you're getting at there, thanks,. |
|
| Author: | MaksimSmelchak [ Fri Dec 17, 2004 3:42 pm ] |
| Post subject: | Constructing a Hellbore |
Hi Dysartes, I built three back in the day so if you'd like more help, please don't hesitate to E-mail me. Shalom, Maksim-Smelchak. |
|
| Author: | KiLLerLooP [ Wed Jan 12, 2005 11:14 pm ] |
| Post subject: | Constructing a Hellbore |
a bit late, but just found the original assembly instruction for a hellbore.. Perhaps anybody can use it |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|