Hm, I was trying to make something reminiscent of this, and didn't notice a lip.
| Attachments: |
|
Edited sponson.JPG [ 48.46 KiB | Viewed 2141 times ] |
| Tactical Command http://www.tacticalwargames.net/taccmd/ |
|
| The Raubtier http://www.tacticalwargames.net/taccmd/viewtopic.php?f=7&t=18207 |
Page 4 of 20 |
| Author: | Spectrar Ghost [ Thu Apr 22, 2010 9:34 pm ] |
| Post subject: | Re: The Raubtier |
I guess my biggest problem is the fact there is no edge to hold the ammo belt in. [[[[[[[[[[| Something like that, with a raised edge top and bottom. |
|
| Author: | Nik [ Thu Apr 22, 2010 9:57 pm ] |
| Post subject: | Re: The Raubtier |
Spectrar Ghost wrote: I guess my biggest problem is the fact there is no edge to hold the ammo belt in. [[[[[[[[[[| Something like that, with a raised edge top and bottom. Actually it will not matter anyways - the detail is so small you will barely notice it with the plain eye. Unless you are used to use magnifiers when handling your minis that is >:D On a serious note: keep in mind that these 3D models are way bigger than what you will get once its finished... |
|
| Author: | Otterman [ Thu Apr 22, 2010 9:58 pm ] | ||
| Post subject: | Re: The Raubtier | ||
Hm, I was trying to make something reminiscent of this, and didn't notice a lip.
|
|||
| Author: | Spectrar Ghost [ Thu Apr 22, 2010 10:04 pm ] |
| Post subject: | Re: The Raubtier |
Ahhh. If you look at that closely, there are links at the front and back of the belt to hold it together. this picture shows better what it might look like. |
|
| Author: | Legion 4 [ Thu Apr 22, 2010 10:39 pm ] |
| Post subject: | Re: The Raubtier |
Whatever is easist ... whatever works ... I'm easy !! 
|
|
| Author: | BlackLegion [ Fri Apr 23, 2010 7:08 am ] |
| Post subject: | Re: The Raubtier |
Well it's not really a box. The box holding the ammunition is located at the inside of the "Riveter" ( = between Riveter and the Raubtiers hull) and from there there goes an ammo belt to the underside of the weapon. |
|
| Author: | Grimgork [ Fri Apr 23, 2010 12:22 pm ] |
| Post subject: | Re: The Raubtier |
Ahhh...I finally got the name Took a while for the coin to drop Good luck doing this Otterman 
|
|
| Author: | Otterman [ Fri Apr 23, 2010 1:39 pm ] |
| Post subject: | Re: The Raubtier |
Heya Black Legion, how are these things deployed in the chaos lists? In groups of 4, like the Armageddon SM list? I may have to revisit my plans for this given Manchurian costs and other non-ordered activity on the board. |
|
| Author: | Evil and Chaos [ Fri Apr 23, 2010 1:42 pm ] |
| Post subject: | Re: The Raubtier |
Otterman wrote: Heya Black Legion, how are these things deployed in the chaos lists? In groups of 4, like the Armageddon SM list? In groups of 4-8. |
|
| Author: | BlackLegion [ Fri Apr 23, 2010 1:42 pm ] |
| Post subject: | Re: The Raubtier |
4 to 8 tanks. |
|
| Author: | AxelFendersson [ Fri Apr 23, 2010 1:46 pm ] |
| Post subject: | Re: The Raubtier |
In companies of 4-8 vehicles that may be any combination of Raubtiers and Grundräubers. |
|
| Author: | berzerkmonkey [ Fri Apr 23, 2010 2:41 pm ] |
| Post subject: | Re: The Raubtier |
Otterman wrote: I may have to revisit my plans for this given Manchurian costs and other non-ordered activity on the board. How so? If it is a financial issue, I'm sure there would be enough interest to cover the initial printing and casting... That being said, how much does something like this cost to get off the ground? 
|
|
| Author: | Otterman [ Fri Apr 23, 2010 2:47 pm ] |
| Post subject: | Re: The Raubtier |
Somebody I know told me these numbers: $20 for a blue $60 for bronzing $160 for metal mastering and production molds $X sculpting agreement with original 3D designer |
|
| Author: | Dave [ Fri Apr 23, 2010 2:57 pm ] |
| Post subject: | Re: The Raubtier |
Since we're throwing out random numbers... 16. |
|
| Author: | Spectrar Ghost [ Fri Apr 23, 2010 4:09 pm ] |
| Post subject: | Re: The Raubtier |
Otterman wrote: Somebody I know told me these numbers: $20 for a blue $60 for bronzing $160 for metal mastering and production molds $X sculpting agreement with original 3D designer Do you know if the original designer get any rate reductions if s/he uses a lot of spin time? That's less then I expected, though still a significant chunk given it's all preproduction costs. |
|
| Page 4 of 20 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
