Here is a more developed result from adding a couple fiddly bits. Pretty quick conversion if you were looking to add in maybe 2 or 3 per base.
| Tactical Command http://www.tacticalwargames.net/taccmd/ |
|
| Anyone know of 6mm flamethrower engineers... http://www.tacticalwargames.net/taccmd/viewtopic.php?f=7&t=16058 |
Page 1 of 2 |
| Author: | The_Real_Chris [ Sat Jul 04, 2009 6:51 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
.. that match epic scale gear? The old WWII chaps I had (minifigs?) were too small compared tot he monster huans of the 41st millenium. |
|
| Author: | Legion 4 [ Sun Jul 05, 2009 5:07 am ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
I thought GHQ infantry was a little smaller than Epic ? |
|
| Author: | The_Real_Chris [ Sun Jul 05, 2009 6:18 am ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Yes my GHQ before they were nicked were definatively smaller - maybe you are thinking of Adler? |
|
| Author: | Legion 4 [ Sun Jul 05, 2009 4:22 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Hmmm ...good to know ... Thanks ! |
|
| Author: | Ghudra [ Sun Jul 05, 2009 5:19 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Would a bit of styrene rod fit the bill? A little chop & tack gets you pretty close to a flamethrower. Add some wire for a hose if you really want to go over the top. |
|
| Author: | Otterman [ Sun Jul 05, 2009 6:48 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
I love you, dude. |
|
| Author: | Ghudra [ Sun Jul 05, 2009 7:40 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
| Here is a more developed result from adding a couple fiddly bits. Pretty quick conversion if you were looking to add in maybe 2 or 3 per base. |
|
| Author: | BlackLegion [ Sun Jul 05, 2009 8:29 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Very cool 
|
|
| Author: | GlynG [ Sun Jul 05, 2009 8:36 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Looks cool! I’d be tempted to go a little further and change the end of the barrel to be W40k flamer shaped, with a piece of plasti-card. Then take a ludicrously small drill bit and drills some holes in it. |
|
| Author: | Apocolocyntosis [ Sun Jul 05, 2009 8:48 pm ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Very effective  As an alternative to plasticard for the flamer end you could use green stuff and poke it with a needle? I recon plasticard would look better tho - I just hate using 0.3mm drill bits as the GW pin vice i use doesn't hold them well 
|
|
| Author: | Ghudra [ Mon Jul 06, 2009 1:09 am ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
Quote: (GlynG @ 05 Jul. 2009, 12:36 ) Looks cool! I’d be tempted to go a little further and change the end of the barrel to be W40k flamer shaped, with a piece of plasti-card. Then take a ludicrously small drill bit and drills some holes in it. Drilling holes is a wee bit daunting, but here is about as ludicrous as I would care to get on a single 6mm trooper. Fun in a "I have too much time on my hands" kind of way. 
|
|
| Author: | zombocom [ Mon Jul 06, 2009 1:21 am ] |
| Post subject: | Anyone know of 6mm flamethrower engineers... |
That's freaking awesome. |
|
| Page 1 of 2 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|